Incorrect Fuinction Error

Discussion in 'CloneDVD' started by LoadMasterC141, Oct 5, 2007.

  1. LoadMasterC141

    LoadMasterC141 New Member

    I am trying to create a personal backup of a DVD called Sporty's IFR Flight Training.

    I must have the most current versions of AnyDVD and CloneDVD2 because I just downloaded the trial versions this evening.

    I did have NERO 8 Demo and DVD43 but uninstalled them. I still have ImgBurn, AoA DVDCopy, Roxio, and DVD Shrink installed though.

    My computer is a DELL XPS 3.4 Dual Core, 2 gig Ram, WinXP latest greatest build, Twin 10kRPM 80 Gig Maxtors in RAID 0 config, and a burner and DVD-ROM. Names listed in ANYDvd Quotes below.

    I went into CloneDVD2, Selected the D drive and next. Then I selected DVD-5, I can't use DVD+-R right?. Anyway, I hit next, selected 8X, then Next. Everything was checked so I just kept hitting next. I got the below error 4 times in a row, exactly at 18%

    [​IMG]

    Here are my AnyDVD quotes:
    For the disk to be burned FROM:
    For The Burner:
    I hope that is normal because there IS a blank SONY DVD+R V1.3 1-16X Blank Disc in there.
     
  2. Charlie

    Charlie Well-Known Member

    Try cleaning the disc and try a different drive if possible as some drives are more forgiving than others.
     
  3. LoadMasterC141

    LoadMasterC141 New Member

    Unfortunately I just have the two drives. This disk is brand new though. It has never even been watched yet.
     
  4. Charlie

    Charlie Well-Known Member

    Return it for another copy is what I suggest as this is a bad source disc.
     
  5. LoadMasterC141

    LoadMasterC141 New Member

    OK I put another DVD in there and it appears to be going past the magical 18 number now.

    Next question....How come my DVD-RW says there is no disk in it?

    Should the write section be "idle" during the whole creation process?
     
  6. mike20021969

    mike20021969 Well-Known Member

    yes.it is idle until creating dvd files reaches 100%.

    have you tried anydvd to 'Rip Video DVD to Harddisk'?,the use clonedvd2 to burn them to dvd?
    does that work?

    RIPVIDEODVDTOHARDDISK.jpg
     
    Last edited: Oct 5, 2007
  7. Webslinger

    Webslinger Retired Moderator

    1) a) Uninstall dvd43 and ensure it's not running at the same time as Anydvd. dvd43 is completely useless if you own Anydvd

    b) Ensure no packet writing software exists on your system (including Roxio's Directcd, Nero's Incd, Roxio/Sonic's DragtoDisc, Drive Letter Access, CyberLink InstantBurn, etc.)

    2) i. For XP with ide burners
    Click this

    Do what it says to do if you have XP and an ide burner/optical drive.

    ii. For Vista with ide burners

    Go into device manager, and check to ensure you're using standard Microsoft ide busmaster drivers.

    Right click on your PCI IDE Bus Master controller, and remove it. Ensure that it also removes the driver for your DVD/CD rom. Reboot. Your system should find hardware. After your system is finished installing hardware, reboot again.

    click http://forum.slysoft.com/showpost.php?p=48880&postcount=20 to get a better idea of what I'm asking for if you're using Vista.


    3. a) Download imgburn. It's a free program: http://www.imgburn.com/index.php?act=download
    (it's also an excellent program imo)

    b) Go to Tools > Filter Driver Load Order. Click "Clipboard". Then paste the information you pasted into your clipboard into your next post (ctrl-v).

    4) Download Nero cd-dvd speed. It's a free program. With Anydvd running in the background, select the tab labeled "scandisc". Select the appropriate drive letter, and click "start". If Nero cd-dvd speed reports read errors, your disc is (probably) bad and needs to be exchanged--even if it plays fine (or your optical drive could be slowly dying).


    5) The original disc has no protection at all on it. That means any program can handle that disc.
     
    Last edited: Oct 5, 2007
  8. Coaster

    Coaster Well-Known Member

    @ LoadMasterC141,

    You do not have a Region set for your DVD device. For the AnyDVD software program to operate and function properly requires that the DVD device have a Region set.

    For information on how to correctly set a DVD device Region suggest reviewing item #14 b ->

    http://forum.slysoft.com/showthread.php?t=5091

    Regards,
    Coaster
     
  9. LoadMasterC141

    LoadMasterC141 New Member

    Well apparently my specific burner is a piece of junk from Dell. $3700 for a top of the line system and my burner craps out. If you go to the Dell forums, you'll find it fairly common with the burner. Dell is sending me another. Thanks for all the advice, even though it was not the answer.