If Clonecd isn't working at all, read this

If you're using Vista, then click this.

If you keep getting "your trial has ended" messages, despite using your license key
visit http://forum.slysoft.com/showthread.php?t=196

Spybot's Teatimer may cause problems during installation.

1. Exit out of all Slysoft programs and reinstall

a) Keep your license key file backed up safely
b) Uninstall Clonecd (start-->all programs-->Slysoft--->Clonecd-->Uninstall)
c) Reboot
d) Try running a registry cleaner program at this point like CCleaner
e) Download Clonecd http://static.slysoft.com/SetupClonecd.exe
f) Exit all Slysoft programs (including Anydvd, Clonedvd2, Clonecd, Clonecdtray, Clonedvdmobile, etc.). Check Windows Task Manager if you have to.
g) At this point disable your antivirus and firewall programs
h) Reinstall
i) Reboot
j) Install your license key (if required) http://forum.slysoft.com/showthread.php?t=732
k) At this point enable your antivirus and firewall programs


If that doesn't work go on to step 2.

2. Read http://forum.slysoft.com/showthread.php?t=1307 fully

3. i. For XP with ide burners
Click this

Do what it says to do if you have XP and an ide burner/optical drive.

ii. For Vista with ide burners

Go into device manager, and check to ensure you're using standard Microsoft ide busmaster drivers.

Right click on your PCI IDE Bus Master controller, and remove it. Ensure that it also removes the driver for your DVD/CD rom. Reboot. Your system should find hardware. After your system is finished installing hardware, reboot again.

click http://forum.slysoft.com/showpost.php?p=48880&postcount=20 to get a better idea of what I'm asking for if you're using Vista.


4. a) Download imgburn. It's a free program: http://www.imgburn.com/index.php?act=download
(it's also an excellent program imo)

b) Go to Tools > Filter Driver Load Order. Click "Clipboard". Then paste the information you pasted into your clipboard into your next post (ctrl-v).


OR

visit http://forum.slysoft.com/showpost.php?p=21907&postcount=11 (thanks to Zebadee)
Use one of the programs mentioned, and list your Lowerfilters and Upperfilters in your next post.

Or for XP users only,
Click Start, Run
type regedit
Go to
HKEY_LOCAL_MACHINE\SYSTEM\Current Control Set\Control\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}

We want what's listed in "LowerFilters" and "UpperFilters". List your Lowerfilters and Upperfilters in your next post.

Before you do this visit http://www.cdr-zone.com/forum/about4719.html, and read the first post please, so you can get a better understanding of what is going on.

Do not start randomly deleting filters, please.


5. If Anydvd/Clonecd is locking up at this point, then read http://forum.slysoft.com/showpost.php?p=24297&postcount=4

-----
General Advice

A. Update your burner's firmware (if available)
http://forum.slysoft.com/showthread.php?t=18731
B. Use good quality media (Memorex, Ritek, Princo, Fuji, TDK from Costco, and Maxell that are not made in Japan are not good quality media). Use Taiyo Yuden 8x Premium, Verbatim, Maxell Plus, or Maxell Broadcast Quality
If you use poor quality blank media, then you should expect problems.
visit http://www.redflagdeals.com/forums/showpost.php?p=4764653&postcount=25
and
http://www.redflagdeals.com/forums/showthread.php?p=3976250
C. Try lowering your burn speed (not below 4x; if you have a 16x burner and 16x rated media try writing to it at 12x instead of 16x; an 8x burn speed on 16x rated media wouldn't be a bad idea either). If you're using Verbatim +R DL media, try a 4x burn speed.
D. If you're using +R, +RW, or +R DL media, change the booktype to "dvd-rom"
http://forum.slysoft.com/showthread.php?t=476 (step 3)
E. Avoid sticker labels (they tend to cause problems)

Bad burn quality is notorious around the end of discs and also at layer breaks when using low quality DL media (use Verbatim +R DL media made in Singapore, and change the booktype to "dvd-rom)