"Sorry, Resource data too large"

Discussion in 'CloneDVD' started by kbritt14, Feb 19, 2007.

  1. kbritt14

    kbritt14 New Member

    I'm pretty new to this.
    Trying to copy an original DVD and I get this error. I'm using DVD-R media. Are there original DVDs that cannot be compressed down to copy??
     
  2. Webslinger

    Webslinger Retired Moderator

    Did you select "dvd-5" in Clonedvd2's quality bar?
     
  3. bilbo65

    bilbo65 Well-Known Member

     
  4. kbritt14

    kbritt14 New Member

    No, I used DVD +/- R, is that where I went wrong?
     
  5. Webslinger

    Webslinger Retired Moderator

  6. kbritt14

    kbritt14 New Member

    Thanks!
    Is burning double layer with Verbatim +R DL a better quality than using single layer??.................probably a stupid question, just want to make sure I'm on the right track.

    Thanks again!
     
  7. Webslinger

    Webslinger Retired Moderator

    There's no compression at all when you use a double layer disc. So, yes, the picture quality will be better.

    I am not fond of compression. I will either split video across two single layer discs using Clonedvd2--or use Verbatim +R DL media with Clonecd.

    There is an obvious cost savings in not having to buy Verbatim+R DL media.

    Here is my preferred method of backing up movies:

    http://forum.slysoft.com/showthread.php?t=327

    That said, most people use cheaper single layer blanks and compress.
     
    Last edited: Feb 19, 2007
  8. kbritt14

    kbritt14 New Member

    Thanks for the loads of information. Can't wait to try it out!
     
  9. Webslinger

    Webslinger Retired Moderator

    Have Fun!:agree:
     
  10. trussme

    trussme Well-Known Member

    Webslinger...

    if....I don't care where the layer break is... is it OK to use Clone DVD (without CloneCD) with Verbatim +R DL media. My understanding is that CloneDVD will put the layer break at the "nearest chapter break"...and that is OK with me...so, will I be OK using Clone DVD on +R DL's without Clone CD?
    ....BTW, I usually split those longies over 2 discs...but I just came into a fortune, and now can afford those new 10X Verbatim +R DL's...
     
  11. Webslinger

    Webslinger Retired Moderator

    Yes :agree:
     
  12. Webslinger

    Webslinger Retired Moderator

    The 2.4x Verbatim +R DLs are usually advertised up to 8x, and I haven't had any problems writing to them at 10x either. :clap:
     
  13. mmdavis

    mmdavis Well-Known Member

    Double Layer

     
  14. trussme

    trussme Well-Known Member

    Thanks, Webslinger!

    Appreciate the Tip!....however, my NEC ND RW 3520A
    will only burn at "4X on DL media"...so I just waste $$ buying 10X DL media, don't I?....but "4X" seems be a "safe" burn speed for DL's anyway.
     
  15. Webslinger

    Webslinger Retired Moderator

    Generally, 4x works very well with the Verbatim +R DLs.
     
  16. Webslinger

    Webslinger Retired Moderator

    Generally, 4x works very well with the Verbatim +R DLs. :agree:
     
  17. Whisperer

    Whisperer Well-Known Member

    I have a big stash of Verb 2.4X DL and use CloneCD for the most part.

    A couple of times, when I forgot to downstep the CloneCD burn speed setting from the 8X setting I had last used for my Verb SL disks down to 2.4X, the burn speed progressed at about a 2.4X regardless of the higher speed setting.

    So is CloneDVD capable of burning at overspeed but CloneCD does not? Just curious, will probably continue to keep burn speed set at 2.4X.

    Whisperer
     
  18. Webslinger

    Webslinger Retired Moderator

    I am under the impression both programs follow the information given by the firmware in the burner for the specific blank media you're using, but I could be mistaken.